Abtus ABT4650 RouteScan Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 31

Abtus ABT4650 RouteScan Скачать руководство пользователя страница 22

21

4650-60 Issue 01

7.0

Maintenance

7.1 Before Each Use

Make sure there are no stains, marks or dirt on the lens. After blowing off dirt and
dust, the drag method can be used to remove fingerprints or other contaminants

The lens is of an extremely high grade and is coated with a proprietary
compound. Unlike many other optical coatings of this grade, this compound is
tough enough to be cleaned using the lens tissues and cleaning solution
provided. However, each clean detracts from the life time of the coating and so
direct contact cleaning should be kept to a minimum.

NEVER touch the lens with anything other than the lens tissues provided

NEVER use high pressure air to remove dirt/dust from the lens

NEVER use a circular motion to clean the lens

7.2 Every 3 Months

Visually inspect the ABT4650 for signs of damage. If necessary, contact your
local distributor for help.

If using the Target Pole accessory, check the Pointed Foot and Rounded Foot for
wear by measuring the length as shown in the figure below. The foot should be
replaced if it has worn by more than 1mm.

Figure

7.3 Annually

The ABT4650 is approved for use in the UK in areas of 3

rd

rail. An annual

electrical insulation test should be carried out.

The ABT4650 must be returned to Abtus Ltd annually for re-calibration to ensure
measurements are within specification. The ABT4650 will also be tested for
electrical insulation compliance at the same time. If using the Target Pole
accessory, this should be re-calibrated at the same time.

«
...
20
21
22
23
24
...
»

Содержание ABT4650 RouteScan
































Отзывы:

Нет отзывов