Absolare Phono Stage Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 13

Absolare Phono Stage Скачать руководство пользователя страница 10

10

ABSOLARE Phono Stage User Manual 1.2

7. Troubleshooting and Maintenance

Surface of the unit is dirty

- Clean with a slightly damp cloth

No power indicator light on both units

- Check AC line voltage, check the fuse
of the Power Supply unit

Power indicator light on Power Supply
but not on Signal Stage

- Check all DC power cords

Both indicator lights are on but tube
heaters are not glowing

- Check all DC power cords

Both indicator lights are on, tube heaters
are glowing, but no sound

- Check all DC power cords

- Check the input selector

- Check resistor loading (custom level is
short circuited as factory default)

- Check output cables

Noise / hum in the sound

- Check grounding of input cables

- Check resistor loading (47K setting may
increase noise)

Input selector does not work

- Check all DC power cords

If the problem is persistent, contact your nearest ABSOLARE dealer.

«
...
8
9
10
11
12
...
»

Содержание Phono Stage














Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды