ABSCO SHEDS CYCSKRSK Скачать руководство пользователя страница 1

Страница: 1 / 21

Absco Industries

Assembly Instruction Manual

SKILLION SHED

N3/C1 FRAME KIT

FOR SPACE SAVER AND

Model: CYCSKRSK

02/03/21

1.1

REVERSE SKILLION MODELS

DOWNLOAD

OUR APP FOR

ASSEMBLY

VIDEOS

LEAVE A REVIEW

Tell us about your experience and

receive a $20 Coles Gift Card.

Visit

www.abscosheds.com.au/review

AU: 1800 029 701

NZ: 0800 466 444

[email protected]

www.abscosheds.com.au

This kit is applicable to the following sheds:

The addition of this frame kit will increase the
wind rating of the specified sheds to

Wind rating: N3/C1 as per AS4055-2012.
Suitable for specific cyclonic regions

30152SK
30151SK
23151SK
23151RSK

WARNING: This shed must be anchored to a
100mm thick concrete slab with the concrete
anchors supplied.
Failure to do so will result in the shed not
having the structural integrity required to
endure a severe storms or cyclonic event.

WARNING: Doors must remain closed with
all padbolts properly secured during severe
storms or cyclonic event.

Where information conflicts with the original
non-cyclonic instruction manual, this
document is to be referenced.

View of frame kit applied to

30152SK

Содержание CYCSKRSK






















Результаты поиска

Содержание CYCSKRSK

Отзывы:

Бренды по названию

Популярные бренды

ABSCO SHEDS CYCSKRSK, Руководство пользователя

Результаты поиска

Содержание CYCSKRSK

Отзывы:

Бренды по названию

Популярные бренды