ABSCO SHEDS 52233WECOK Скачать руководство пользователя

Страница: 1 / 45

Absco Industries

Assembly Instruction Manual

ABSCO WORKSHOP SHED

MODEL: 52233WECOK

5.22mW x 2.26mD x 2.00mH

Model: 52233WECOK

25/11/2021

1.3

DOWNLOAD

OUR APP FOR

ASSEMBLY

VIDEOS

PLEASE LEAVE A REVIEW

Tell us about your experience!

Visit

www.abscosheds.com.au/review

AU: 1800 029 701

N Z: 0800 466 444

[email protected]

www.abscosheds.com.au

CONCRETE S

LAB

5320mm

2360m

When laying concrete slab, ensure there
is a rebated edge 25mm deep around
the perimeter. This will help water egress
from the base of the shed.

ABSCO INDUSTRIES

ASSEMBLY INSTRUCTION MANUAL

SHED MODEL: 23151GK

21-11-2017

CONCRETE SLAB

2360mm

1620mm

FRONT: 2.26m

SIDE: 1.52m

HEIGHT: 1.95m

We thank you for choosing an Australian made

shed. For further assistance please visit our detailed

instructional video library at

Http://www.abscosheds.com.au/watch-videos

At ABSCO Industries we are always looking to be

number ONE, so please let us know what you think

of our instructions. Feedback makes us better.

[email protected]

CONCRETE

REBATED EDGE

BOTTOM CHANNEL

CONCRETE SLAB

75mm WIDE REBATE

100mm

WHEN LAYING YOUR CONCRETE

SLAB, ENSURE THERE IS A

REBATED EDGE 25mm DEEP

AROUND THE PERIMETER

THIS WILL HELP WATER EGRESS

FROM THE BASE OF THE SHED

Absco Industries

Premier Shed Model: 23151GK

PAGE 01

For construction in non-cyclonic areas

Wind rating: N2 as per AS4055-2021.
If you require a higher wind rating please contact
us: [email protected] or 1800 029 701

NOTE: This shed can be upgraded to wind rating:
C1 as per AS4055-2021 with the additional purchase
of a Cyclone Kit.

Содержание 52233WECOK














































Результаты поиска

Содержание 52233WECOK

Отзывы:

Похожие инструкции для 52233WECOK

Бренды по названию

Популярные бренды

ABSCO SHEDS 52233WECOK, Руководство пользователя

Результаты поиска

Содержание 52233WECOK

Отзывы:

Похожие инструкции для 52233WECOK

Бренды по названию

Популярные бренды