Abov MC96F6432A Скачать руководство пользователя

Страница: 81 / 281

MC96F6432A

ABOV Semiconductor Co., Ltd.

Interrupt Controller

10.1 Overview

The MC96F6432A supports up to 23 interrupt sources. The interrupts have separate enable register bits and allows

software control. They can also have four levels of priority assigned to them. The non-maskable interrupt source is

always enabled with a higher priority than any other interrupt source and is not controllable by software. The interrupt

controller has following features:

−

The request from 23 interrupt source

−

6 group priority

−

4 priority levels

−

Multi Interrupt possibility

−

If the requests of different priority levels are received simultaneously, the request of higher priority level is

served first.

−

Each interrupt source can be controlled by EA bit and each IEx bit

−

Interrupt latency: 3~9 machine cycles in single interrupt system

The maskable interrupts are enabled through four pair of interrupt enable registers (IE, IE1, IE2, IE3). Bits of IE, IE1,

IE2, IE3 register individually enable/disable a particular interrupt source. Overall interrupts are controlled by EA (bit 7 of

IE). When EA is set to

‘0’, all interrupts are disabled: when EA is set to ‘1’, interrupts are individually enabled or

disabled through the other bits of the interrupt enable registers. The EA bit is always cleared to

‘0’ jumping to an

interrupt service vector and set to

‘1’ executing the [RETI] instruction. The MC96F6432A supports a four-level priority

scheme. Each maskable interrupt is individually assigned to one of four priority levels according to IP and IP1.

Default interrupt mode is level-trigger mode basically, but if needed, it is possible to change to edge-trigger mode.

Table 10.1 shows the Interrupt Group Priority Level that is available for sharing interrupt priority. Priority of a group is

set by two bits of interrupt priority registers (one bit from IP, another one from IP1). Interrupt service routine serves

higher priority interrupt first. If two requests of different priority levels are received simultaneously, the request of higher

priority level is served prior to the lower one.

Содержание MC96F6432A


























































































































































































































































































Результаты поиска

Содержание MC96F6432A

Отзывы:

Похожие инструкции для MC96F6432A

Бренды по названию

Популярные бренды

Abov MC96F6432A, Руководство пользователя

Результаты поиска

Содержание MC96F6432A

Отзывы:

Похожие инструкции для MC96F6432A

Бренды по названию

Популярные бренды