ABL eMH3 Скачать руководство пользователя

Страница: 60 / 66

| Appendix –

Standards and guidelines

Model code

3W2250

3W2251

Ambient temperature

-30°C to 50°C

Storage temperature

-30°C to 85°C

Relative humidity

5 to 95%, no condensation

Class of protection

Degree of protection (housing)

IP54

Overvoltage category

III

Impact strength

IK08

Dimensions (H × W × D)

492 × 394 × 189 mm

(housing base incl. mounting plate, without overhangs)

Weight per unit

approx. 10 kg

approx. 15 kg

Standards and guidelines

General standards

2014/30/EU

EMC Guideline

2011/65/EU

RoHS Guideline

2012/19/EU

WEEE Directive

2014/35/EU

Low voltage directive

Standards governing electromagnetic interference (EMV)

IEC 61851-21-2

Conductive charging systems for electric vehicles – Part 21-2: EMC requirements for off

board electric vehicle charging systems

Device safety standards

IEC 61851-1 Ed. 3

Electrical equipment for electric road vehicles - conductive charging systems for electric

vehicles – Part 1: General requirements

IEC 60364-7-722 Ed. 1

Low voltage installations - Part 7-722: Requirements for special installations or locations -

Supply of electric vehicles

Trademarks

All trademarks mentioned in this manual, including those that may be protected by third parties are, without restric-

tion, subject to the regulations of the respectively applicable trademark law and the property rights of the respective

registered owners. All trademarks, trading names or company names marked here as such are, or may be, trademarks

or registered trademarks of their respective owners. All rights not explicitly granted here are reserved.
The absence of explicit identification of trademarks used in this manual must not lead to the conclusion that a name

is free from the rights of third parties.

Data cable recommendations

The following data cables are recommended for wiring up the bus interfaces in the Wallbox eMH3:

Designation

Cross section

Number

Cat5e

from at least 0.14 mm²

1 cable per connection

between two wallboxes

Cat6

from at least 0.14 mm²

WARNING!

Selecting suitable data cables

Please note that these are recommendations only: the conductor cross-section must be adjusted according to the

cable length by the specialist electrical contractor responsible for installation.

Содержание eMH3



































































Результаты поиска

Содержание eMH3

Отзывы:

Похожие инструкции для eMH3

Бренды по названию

Популярные бренды

ABL eMH3, Руководство по установке

Результаты поиска

Содержание eMH3

Отзывы:

Похожие инструкции для eMH3

Бренды по названию

Популярные бренды