6
GB
OPERATING FUNCTIONS (Figs. 1, 2 and 4):
1 = Mains switch (Emergency-stop) (fig. 1)
This switch turns the machine either on
(position „1“) or off (position „0“).
2 = „Cutting system forward“
pushbutton (fig. 2)
Pressing this button starts the cutting system.
Material can now be fed to the shredder.
3 = „Cutting system stop“
pushbutton (fig. 2)
Pressing this button switches the shredder
off, thereby halting the cutting system.
4 = „Cutting system reverse“
pushbutton (fig. 2)
Pressing this button starts the cutting system
in reverse.
5 = Pilot lamp (fig. 2)
a) „ready“
Continously lights when the mains switch
(1) is operated.
b) „motor protection“
Flashes when the motor is overloaded.
While the motor is cooling down, the
machine cannot be switched on to „forward“
run.
6 = Pilot lamp „paper jam“ (fig. 2)
Lights when too much paper is fed to the
cutters (see description „AUTOMATIC
RESPONSE IN CASE OF OVER-
LOADING“).
7 = Pilot lamp (fig. 2)
a) „door open“/„hopper open“
Lights when the door is not closed or when
the hopper is open. The machine then
switches off automatically and it cannot be
started as long as the door is open or the
hopper is open.
b) „collecting bag full“ (fig. 2)
Lights as soon as the collecting bag is full
and needs to be emptied. At the same time
the machine switches off automatically.
8 = Light barrier (forward operation) (fig. 4)
The shredding operation is started as soon
as a sheet of paper passes through the feed
slot.
OPERATION
OPERATING THE MACHINE:
To start, switch on the unit by operating the mains
switch (1) (fig. 1). The pilot lamp marked „ready for
operation“ (5), as well as the red stop-button „S“
(3) (fig. 2) will light to indicate that the machine is
ready for operation.
The paper tray may not be used as a
step ladder or as a seat. Danger of
tipping over!
FEEDING CRUMPLED PAPER
(MODEL 852CC):
In order to avoid a reduction of user
safety by increasing the height of the
hopper side panels, and in order to
allow for filling the hopper while
standing on the floor, the height of the
hopper side panels is not in compliance
with EN 294:1992.
The deviation from EN 294:1992 is
identified with a yellow-black mark.
1. Fill the hopper with crumpled paper.
Note: The crumpled paper can be dropped
directly from the wastepaper basket into the
hopper of the machine. The apportioning wings
preceding the cutting mechanism ensure more
or less uniform distribution of the paper.
Attention: The wastepaper basket is no refuse
tin and should not be emptied into the machine
thoughtlessly - in no way can the machine
destroy bottles, pens, pencil sharpeners etc.
2. Press the pushbutton switch „forward“ (2) (fig.
2). The cutting system runs and begins to shred
the paper.
Note: Do not feed any smooth paper until the
crumpled paper is completely shredded.
3. To switch the machine off press the red stop-
button (3) (fig. 2).
FEEDING SMOOTH PAPER:
- Feed smooth paper through the opening at the
lower part of the hopper (model 852CC) or
through the opening of the hopper (model 802CC)
to the cutting system.
- Machine switches automatically to forward and
draws paper in.
- The machine switches off automatically after
shredding.
Never feed the shredder with a quantity
of paper exceeding the maximum
indicated in the technical details.
Should the machine be overfed, follow
the instructions under „AUTOMATIC
RESPONSE IN CASE OF
OVERLOADING“.
AUTOMATIC RESPONSE
IN CASE OF „OVERLOADING“:
In case you accidentally overload the shredder, it
will automatically alleviate the problem as follows:
1. The cutting system becomes jammed. The pilot
lamp (6) (fig. 2) lights up.
2. The cutting system runs briefly in reverse,
thereby freeing the material to be shredded.
3. The cutting system automatically switches back
to forward mode.
The machine repeats this process until all the
material has been shredded satisfactorily.
EMPTYING THE COLLECTING BAG (Fig. 3):
When the collecting bag is full, the machine turns
off automatically. The pilot lamp (7) (fig. 2) lights
up. Empty the collecting bag as follows:
- Open the door and take out the sliding frame
with the collecting bag.
- Remove the rubber band, take out the full bag
and dispose of contents.
- Put the empty bag from below through the
sliding frame and put the edges of the bag
approx. 10 cm over the frame outwardly.
- Fix the collecting bag with the rubber band at the
sliding frame.
- Move back the sliding frame with the collecting
bag and close door.
Note: The machine will only run with closed door!
fig. 1
MAINS SWITCH
I
1
fig. 3
fig. 2
3
2
5
6
7
4
S
Schleicher International
802CC
852CC
1-800-658-8788 - www.abcoffice.com
