ABB XIO-00 Скачать руководство пользователя страница 41

Страница: 41 / 207

XIO USER MANUAL | 2106424MNAB |

Figure 4-8: Default IP configuration

The following table lists the cabling details for connecting to the XIO Ethernet ports.

Table 4-2: Ethernet cabling

Supported devices
(with Ethernet 10/100 BaseT ports)

Required cabling termination

(connectors) or adaptors

ABB part number

Host system (operator laptop or computer)

Straight-through Ethernet CAT 5

cable with RJ-45 connectors at

both ends.

1681011
Maximum distance:
100 meters
(328 feet)

Network device (Ethernet hub, switch or router)
Other Totalflow devices: additional XIOs, RMCs,

flow computers, and analyzers

IMPORTANT NOTE:

Operators can initially connect to any of the 4 ports and use the same factory

default address when the XIO is configured in 4-port switch mode. For other modes and

configurations, use the appropriate IP address and port for local communication. Access to an

Ethernet port for direct connection depends on the final connection topology of the XIO and other

devices after the installation is complete.

Configure the host system

Configuration of the host system may or may not be needed:

–

If the laptop is configured to automatically obtain the IP address, do not change the TCP/IP

configuration. Proceed to section

4.3.2.2 Set up PCCU32 and connect

Содержание XIO-00
















































































































































































































Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды

ABB XIO-00, Руководство пользователя

Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды