ABB XIO-00 Скачать руководство пользователя страница 180

Страница: 180 / 207

180

| XIO USER MANUAL | 2106424MNAB

Figure 9-1: Incorrect Ethernet connections for an XIO in 4-port switch mode

Legend: Incorrect use of Ethernet connections

Description

Third party Ethernet switch or hub

XIO

9.1.2

Ethernet modes

The connections supported by the XIO depend on the configuration of the Ethernet interfaces. The

interfaces support several modes of operation, and these modes need to be taken into consideration when

planning connections.
The supported modes on the XIO are:

–

4-port switch mode: factory default. All 4 Ethernet interfaces are logically combined into a single

network. The 4 ports switch traffic between each other.

–

1 network mode: supported by the enterprise ports only. The two enterprise ports are logically

combined into a single network (ports switch traffic between each other).

–

2 network mode: supported by both the enterprise and industrial ports. Each set of Ethernet

interfaces are isolated into individual ports, each assigned to its own network. Traffic on each of the

ports is isolated from the other ports. Communication in each is independent of the others.

9.2

IP parameter configuration

Ethernet connectivity requires the correct IP parameters for connecting systems. To configure a host

system, controllers, flow computers or any other device supporting native Ethernet interfaces, each

system must have a unique and valid IP address, the correct associated subnet mask, and a gateway (if

remote or network communication is required).

IMPORTANT NOTE:

IP addressing depends on the number of Ethernet interfaces or ports

on the device and their configuration mode. Devices with multiple Ethernet interfaces may

require more than one IP address. Consult the network administrator to determine the

appropriate configuration for each specific scenario. See section

9.2.1

for additional details

or see PCCU online help topics.

Содержание XIO-00
















































































































































































































Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды

ABB XIO-00, Руководство пользователя

Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды