ABB XIO-00 Скачать руководство пользователя страница 171

Страница: 171 / 207

XIO USER MANUAL | 2106424MNAB |

171

8.5.2

Warm restart with the RESET button

The warm restart resets the XIO microprocessor. Use a warm restart to take the XIO out of service for

maintenance or troubleshooting. Only use a warm restart when a power or communication interruption

causes the microprocessor to lock up.
This procedure uses the RESET button on the XIO to restart the device. It causes the device to restart

with the running (warm) configuration. If the XIO is installed inside an enclosure, you must have access to

the interior of the enclosure to access the XIO reset button.
To complete a warm restart using the reset button:

Figure 8-27: Security switch

Legend: Security switch

Description

Security switch

Reset (paperclip actuated)

Cold (paperclip actuated)

IMPORTANT NOTE:

If the XIO does not restart, press and hold the

Reset

button for eight

seconds.

8.5.3

Warm restart from the device loader

This procedure performs the warm restart from the 32-bit loader. The procedure can be performed while

on a local or remote loader connection.
The procedure causes the device to restart with the running (warm) configuration.
To complete a warm restart from the device loader:

Содержание XIO-00
















































































































































































































Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды

ABB XIO-00, Руководство пользователя

Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды