ABB UNO-DM-2.0-TL-PLUS Скачать руководство пользователя страница 87

Страница: 87 / 198

- 87 -

000693DG

5 - Installation

onnection and configuration of the ABB B21 meter

(single-phase)

The indications set out below are necessary to connect the meter to the inverter. Always refer

to the specific documentation supplied with the ABB B21.

The energy meter ABB B21

is a DIN rail device (2 modules) and must be

installed where the electricity supply is single-phase.

To avoid risks of electrical shock, all wiring operations must be carried out with the AC disconnect

switch (or the supply meter) upstream of the meter disconnected.

• Disconnect the AC disconnect switch upstream of the meter.

• Strip the insulation of the cable for the length which is indicated on the

meter (13mm).

• Connect the cables of the single-phase line in accordance with the la-

yout printed on the meter (L and N) to the AC connection terminal block

and tighten the screws (tightening torque 3.0 Nm).

COMM

COMM.

to Accessory

board

TO GRID

LOADS and INVERTER SIDE

Содержание UNO-DM-2.0-TL-PLUS







































































































































































































Результаты поиска

Содержание UNO-DM-2.0-TL-PLUS

Отзывы:

ABB UNO-DM-2.0-TL-PLUS, Руководство пользователя, Страница: 87 / 198

Результаты поиска

Содержание UNO-DM-2.0-TL-PLUS

Отзывы: