ABB TZIDC-200, Руководство пользователя

Страница: 27 / 40

TZIDC-200
DIGITAL POSITIONER | CI/TZIDC-200/C-FM-US-EN REV. B 27
Electrical data for inputs and outputs
Note
When using the device in potentially explosive atmospheres,
note the additional connection data in
Use in potentially
explosive atmospheres
on page 5!
Analog input
Set point signal analog (two-wire technology)
Terminals +11 / −12
Nominal operating range 4 to 20 mA
Split range configuration
between
20 to 100 % of the nominal operating range can be
parameterized
Maximum 50 mA
Minimum 3.6 mA
Starting at 3.8 mA
Load voltage 9.7 V at 20 mA
Impedance at 20 mA 485 Ω
Digital input
Input for the following functions:
•
no function
•
move to 0 %
•
move to 100 %
• Hold previous position
• block local configuration
• block local configuration and operation
• block any access (local or via PC)
Binary input DI
Terminals +81 / -82
Supply voltage 24 V DC (12 to 30 V DC)
Input ‘logical 0’ 0 to 5 V DC
Input ‘logical 1’ 11 to 30 V DC
Input Current maximum 4 mA
Digital output DO
Output configurable as alarm output by software.
Binary output DO
Terminals +83 / −84
Supply voltage 5 to 11 V DC
(Control circuit in accordance with DIN
19234/NAMUR)
Output ‘logical 0’ > 0.35 mA to < 1.2 mA
Output ‘logical 1’ > 2.1 mA
Direction of action Configurable
‘logical 0’ or ‘logical 1’
Option modules
Plug-in module for analog feedback AO*
Without any signal from the positioner (e.g. ‘no power’ or
‘initializing’) the module sets the output to > 20 mA (alarm level).
Terminals +31 / -32
Signal range 4 to 20 mA (split ranges can be parameterized)
• in the event of an error > 20 mA (alarm level)
Supply voltage, two-wire
technology
24 V DC (11 to 30 V DC)
Characteristic curve rising or falling (configurable)
Deviation < 1 %
Plug-in module for digital feedback SW1, SW2*
Two software switches for binary position feedback (position
adjustable within the range of 0 to 100 %, ranges cannot
overlap)
Terminals +41 / -42, +51 / -52
Supply voltage 5 to 11 V DC
(Control circuit in accordance with DIN 19234 /
NAMUR)
Output ‘logical 0’ < 1.2 mA
Output ‘logical 1’ > 2.1 mA
Direction of action Configurable
‘logical 0’ or ‘logical 1’
* The module for analog feedback and the module for digital feedback have
separate slots and can be used together.
Mechanical digital feedback
Two proximity switches or microswitches for independent
signaling of the actuator position, switching points are
adjustable between 0 bis 100 %.
Feedback on the actuator position using proximity switches Limit 1, Limit 2
Terminals +41 / -42, +51 / -52
Supply voltage 5 to 11 V DC
(Control circuit in accordance with DIN
19234/NAMUR)
Direction of action Metal tag in the
proximity switch Metal tag outside the
proximity switch
Type SJ2-SN (NC; log 1) < 1.2 mA > 2.1 mA
Feedback on the actuator position using microswitches Limit 1, Limit 2
Terminals +41 / -42, +51 / -52
Supply voltage maximum 24 V AC/DC
Load rating Maximum 2 A
Contact surface 10 µm Gold (AU)
Mechanical position indicator
Indicator disk in enclosure cover linked with device feedback
shaft.
These options are also available for retrofitting by Service.