ABB Turbocharger A130-M Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 24

ABB Turbocharger A130-M Скачать руководство пользователя страница 15

Assembly Instructions / A130-M.. - A145-M

4 Installing the turbocharger / 4.4 Fastening the turbocharger with a
standard nut

© Copyright 2020 ABB. All rights reserved.

HZTL455311P0005_EN

Rev.B

July 2020

¡

Fastening the turbocharger with a clamping nut

The gas outlet casing (61001) may still be fitted in the exhaust gas pipe if the locking nuts
remain accessible for removing the turbocharger.

4.4

Fastening the turbocharger with a standard nut

u

Fit the nuts and tighten them according to variant 1 or 2 in the table below.

Product

Through hole in

bearing casing

[mm]

Fixing screws

[mm]

Variant 1: Tightening

torques [Nm] **)

Variant 2: Hy-

draulic pre-ten-

sioning forces [kN]

A130

Ø 17

M16

280

110

A135

Ø 21

M20

560

175

A140

Ø 25

M24

960

250

Table 6: Tightening torque for standard nuts

**) When the turbocharger is mounted on the engine support, the bolt threads and screw
heads must be lightly oiled (assumed friction coefficient

µ

= 0.12 for tightening torque)

u

Remove the lifting gear.

Page

13

/

21

«
...
13
14
15
16
17
...
»

Содержание Turbocharger A130-M

























Отзывы:

Нет отзывов