background image

Assembly Instructions / TPX44-H

2  Safety / 2.3  Occupational safety

© Copyright 2019 ABB. All rights reserved.

HZTL455311P0037_EN

Rev.A

November 2019

2.3

Occupational safety

General

 WARNING

Injuries to persons

Severe injuries to personnel or fatal accidents can be caused by mechanical
influences as a consequence of hazardous and inadequate operational pro-
cedures or non-compliance with safety and health standards.

u

When working on the turbocharger always wear safety footwear and pro-
tective clothing to protect against mechanical hazards.

u

Keep personal protective equipment in perfect condition.

u

Obey mandatory signs.

u

Observe the general rules for occupational safety and prevention of acci-
dents.

u

Only perform operations that are described in this document.

u

Only perform operations for which you have received instruction or train-
ing.

Wear safety footwear to protect against mechanical hazard and risk of fall-
ing.

Wear protective clothing.

 WARNING

Risk of falling

When working on the turbocharger, there is a risk of falling.

u

Do not climb onto the turbocharger or onto attached parts and do not
use them as climbing aids.

u

Use suitable climbing aids and working platforms for work above body
height.

u

Only perform work on the turbocharger when you are in a physically and psychologically
stable condition.

u

Only work with suitable tools, equipment and appliances that function properly.

u

Keep the workplace clean; clear away any loose objects and obstacles on the floor.

u

Keep the floor, equipment, and turbocharger clean.

u

Have oil binding agents ready and provide or keep oil pans at hand.

Welding work in the vicinity of the turbocharger

u

When performing welding work in the vicinity of the turbocharger, always cover the filter
silencer to prevent the filter mat from being damaged.

Page 

7

 / 

17

Содержание TPX Series





















Отзывы: