ABB TPS48-H33 Скачать руководство пользователя страница 55

Страница: 55 / 130

Operation Manual / 4 Product description / TPS44-H.. - TPS52-H..

Monitoring operation

Page 25 / 99

HZTL4037_EN

Revision A

August 2016

4.2

Exhaust gas temperature before turbine

CAUTION

Factors influencing replacement intervals
Operation above the operating limits defined on the rating plate can shorten

the recommended replacement intervals considerably.



Measure exhaust gas temperature upstream of turbine.



Comply with operating limits on rating plate.



Definition and explanations concerning rating plate: refer to chapter 2 of Operation Manual /

Safety.



Operating limits: refer to chapter 3 of Operation Manual / Safety data sheet or examine

rating plate.

4.3

Turbocharger speed

4.3.1

Introduction

A speed measuring system enables the constant monitoring of the turbocharger speed.

CAUTION

Do not strain cables
If you pull the speed measurement cables too hard, contacts can be pulled

out.



Do not strain the speed measurement cables by pulling.

CAUTION

Machine damage
Operation above the operating limits defined on the rating plate can shorten

the recommended replacement intervals considerably and cause machine

damage.



Measure turbocharger speed.



Comply with operating limits on rating plate.



Definition and explanations concerning rating plate: refer to chapter 2 of Operation Manual /

Safety.



Operating limits: refer to chapter 3 of Operation Manual / Safety data sheet or examine

rating plate.

If no speed measurement system is present, the system below can be ordered from an ABB

Turbocharging Service Station (see chapter

Ordering spare parts [➙

93]).

Содержание TPS48-H33



































































































































Результаты поиска

Содержание TPS48-H33

Отзывы:

Похожие инструкции для TPS48-H33

Бренды по названию

Популярные бренды

ABB TPS48-H33, Руководство по эксплуатации

Результаты поиска

Содержание TPS48-H33

Отзывы:

Похожие инструкции для TPS48-H33

Бренды по названию

Популярные бренды