manualshive.com logo in svg

ABB TPL-B Series, Руководство по сборке

Поделиться
Скачать
ABB TPL-B Series Скачать руководство пользователя страница 13

Assembly Instructions / TPL85-B14/B15/B16, TPL91-B

4  Installing the turbocharger / 4.1  Steps for fastening the turbochar-
ger

© Copyright 2020 ABB. All rights reserved.

HZTL455311P0020_EN

Rev.A

July 2020

4.1

Steps for fastening the turbocharger

General information

Subject

Requirement / Information

Turbocharger fixing elements

ISO strength class 

≥

 8.8

Washers

Hardened, thickness 

≥

 15 % nominal thread

diameter

Dimension a (compressor end)

a = height of turbocharger foot a

Dimension a (turbine end)

a = height of turbocharger foot F + spacer
sleeve D

Dimension b

Hole in bracket

Dimension c

Thread length 

≥

 1.5 times the nominal thread

diameter

Coefficient of friction

0.12 (lightly oiled)

Table 5

NOTICE

Strength classes of screws

In order to install the turbocharger, screws with a higher strength class than
8.8 can also be used.
The tightening torques and tightening angles remain the same as with
strength class 8.8.

Compressor-end foot

Turbine-end foot

Page 

11

 / 

17

Содержание TPL-B Series





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды