manualshive.com logo in svg

ABB Terra DC Wallbox C UL, Руководство по установке, Страница: 16 / 38

Поделиться
Скачать
Page 16
ABB Terra DC Wallbox C UL Скачать руководство пользователя страница 16

 

TERRA DC WALLBOX UL 

2020-10-05 

 

16/38 

The integrity of the electrical grounding is essential.  Ensure that the equipment grounding terminal is 
used in the device and an actual grounding conductor is installed to provide a path back to the source 
upstream panel. (Do not use the conduit or raceway as the sole equipment grounding conductor). 

3.2.5

 

Conduit for ethernet cable 

The Terra DC Wallbox does not have a hole designated for a conduit carrying only an ethernet cable to 
connect to.  If ethernet cable solution is required for an installation, please contact your ABB sales con-
tact person to review ethernet cable entry solutions. 

3.2.6

 

Specification for ethernet cable 

If the cellular connection is not available, ethernet connection must be made to the charger using a 
shielded 8P+PE ethernet cable with RJ45 connectors.  Additional recommendations include: 

•

 

Maintain distance of 75 meters or less.  Distances over 75 meters require a custom engineered 
solution. 

•

 

Minimum bandwidth: 
upload: 128 kb/s 
download: 4 Mb/s 

•

 

99.9% availability 

•

 

600V rated cable that may route beside input power wires for short distances 

3.3

 

Terra DC Wallbox placement 

Placement of the Terra DC Wallbox must be carefully determined by accounting for charging cable reach, 
Terra DC Wallbox position with respect to parking space, bollards and wheel stops, ventilation and 
working clearances, and other local codes and regulations (e.g. ADA requirements in the USA). 

3.3.1

 

Charging cable reach 

The Terra DC Wallbox charging cables are available in lengths of 3.5 or 7 meters. The charging cables exit 
the charger enclosure on both the right and left sides. The cables and the connectors mounted on the 
cables are different depending on the charging standard and vary in flexibility. 

The figure below shows an example of a dual connector charger with both types of connector and the 
corresponding reach area. The green circle with a continuous line describes the CHAdeMO cable 3.5m 
and the red circle with a continuous line describes the CCS cable 3.5m. The broken lines indicate the 
same cable types with a length of 7 meters (23 ft). 

Содержание Terra DC Wallbox C UL







































Отзывы:

Нет отзывов