ABB Terra 124 Скачать руководство пользователя страница 6

Страница: 6 / 54

About this document

1.1

Function of this document

The document is only applicable for this EVSE (Terra x4), including the variants and

options listed in section

8.1

The document gives the information that is necessary to install the EVSE.

1.2

Target group

The document is intended for qualified installation engineers.

For a description of the required qualifications, refer to section

3.3

1.3

Revision history

Version

Date

Description

001

Initial version

1.4

Language

The original instructions of this document are in English (EN-US). All other language

versions are translations of the original instructions.

1.5

Illustrations

It is not always possible to show the configuration of your EVSE. The illustrations in

this document show a typical setup. They are for instruction and description only.

1.6

Units of measurement

SI units of measurement (metric system) are used. If necessary, the document

shows other units between parentheses () or in separate columns in tables.

1.7

Typographical conventions

The lists and steps in procedures have numbers (123) or letters (abc) if the sequence

is important.

1.8

How to use this document

1. Make sure that you know the structure and contents of this document.

2. Read the safety chapter and make sure that you know all the instructions.

3. Do the steps in the procedures fully and in the correct sequence.

4. Keep the document in a safe location that you can easily access. This document

is a part of the EVSE.

About this document

BCM.S1102.0-EN | 001

Содержание Terra 124






















































Результаты поиска

Содержание Terra 124

Отзывы:

Бренды по названию

Популярные бренды

ABB Terra 124, Руководство по установке

Результаты поиска

Содержание Terra 124

Отзывы:

Бренды по названию

Популярные бренды