ABB Terra 124 Скачать руководство пользователя страница 29

Страница: 29 / 54

Procedure

1. Open the front and right doors. Refer

to section

6.1

2. Loosen the fasteners (A).

3. Move the sliding plate (B) to open the

cable inlet.

4. If it is necessary, remove the cable

gland (C) for the Ethernet cable.

Caution: If the cable gland

for the Ethernet cable is not

used, make sure that the

cable gland is closed and

sealed

5.5.3

Guide the cables through the opening in the cable guide plate

Preliminary requirements

The front and right doors are open.

The cable inlet is open.

Procedure

1. If it is necessary, install the cable

gland (A) over the Ethernet cable (B).

2. Guide the wires (C) of the AC input

cable, the PE wire and the earthing

conductor for the enclosure through

the cable inlet.

3. Pull the wires and cable through the

gland plate and the cable inlet. Apply

the full cable slack.

4. Close the sliding plate (D).

5. Tighten the fasteners (E).

6. Close the doors. Refer to section

6.2

5.5.4

Install the cabinet on the foundation

Preliminary requirements

•

Open spanner

•

Fasteners M10 (bolts and

washers), 8x

Installation

BCM.S1102.0-EN | 001

Содержание Terra 124






















































Результаты поиска

Содержание Terra 124

Отзывы:

Бренды по названию

Популярные бренды

ABB Terra 124, Руководство по установке

Результаты поиска

Содержание Terra 124

Отзывы:

Бренды по названию

Популярные бренды