ABB Terra 124 Скачать руководство пользователя страница 13

Страница: 13 / 54

Note: For Terra 94, the second array of three power modules is empty.

2.3.2

Terra 94, 124 and 184 C

AC input cable

Manual switch

EMC filter

AC contactor

Residual-current device and

breaker

Power module matrix

Power module

DC filter

DC contactor

DC fuse

Overcurrent protection device

Charge cable

Insulation management interface

Charge protocol interface

Surge-protection device

Residual-current device

Heater

Auxiliary power supply

Cabinet controller board

Power bridge

Touchscreen

Cooling fan

LED for the illumination of the

exterior of the EVSE

CAN bus signal 1

CAN bus signal 2

•

Black and bold lines: power connection

•

Black and thin lines: auxiliary power connection

•

Green lines: CAN bus

•

Purple lines: control signal or monitoring signal

Note: For Terra 94, the second array of three power modules is empty.

Description

BCM.S1102.0-EN | 001

Содержание Terra 124






















































Результаты поиска

Содержание Terra 124

Отзывы:

Бренды по названию

Популярные бренды

ABB Terra 124, Руководство по установке

Результаты поиска

Содержание Terra 124

Отзывы:

Бренды по названию

Популярные бренды