ABB Relion SAM600 Скачать руководство пользователя страница 79

Страница: 79 / 92

The block status of a component is shown on the LHMI as the

Blk output under the same path

as for

Beh:Main menu/Test/Function status/Function group/Function block descriptive

name/LN name/Outputs. If the

Blk output is not shown, the component cannot be blocked.

9.8.2

Setting guidelines

M15260-3 v7

Remember always that there are two possible ways to place the IED in the

TestMode= On”

state. If, the IED is set to normal operation (

TestMode = Off), but the functions are still shown

being in the test mode, the input signal IED_TEST on the TESTMODE function block is

activated in the configuration.

Forcing of binary input and output signals is only possible when the IED is in IED test mode.

9.9

Time synchronization TIMESYNCHGEN

IP1750-1 v2

9.9.1

Application

M11345-3 v12

Use time synchronization to achieve a common time base for the IEDs in a protection and

control system. This makes it possible to compare events and disturbance data between all

IEDs in the system.

Time-tagging of internal events and disturbances are an excellent help when evaluating faults.

Without time synchronization, only the events within one IED can be compared with each

other. With time synchronization, events and disturbances within the whole network, can be

compared and evaluated.

In the IED, the internal time can be synchronized from BIN (Binary Minute Pulse), SNTP, and

IEEE 1588 (PTP) source.

The selection of the time source is done via the corresponding setting.

If PTP is activated, the device with the best accuracy within the synchronizing group will be

selected as the source. For more information about PTP, see the Technical manual.

IEEE 1588 (PTP)

PTP according to IEEE 1588-2008 and specifically its profile IEC/IEEE 61850-9-3 for power

utility automation is a synchronization method that can be used to maintain a common time

within a station. This time can be synchronized to the global time using, for instance, a GPS

receiver. If PTP is enabled on the IEDs and the switches that connect the station are

compatible with IEEE 1588, the station will become synchronized to one common time with an

accuracy of under 1us. Using an IED as a boundary clock between several networks will keep

1us accuracy on three levels or when using an HSR, 15 IEDs can be connected in a ring without

losing a single microsecond in accuracy.

9.9.2

Setting guidelines

IP15089-1 v3

All the parameters related to time are divided into two categories: System time and

Synchronization.

9.9.2.1

System time

M11348-119 v6

The time is set with years, month, day, hour, minute, second and millisecond.

1MRK 511 445-UEN B

Section 9

Basic IED functions

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды