ABB Relion SAM600 Скачать руководство пользователя страница 76

Страница: 76 / 92

Operational departments can plan for different operating conditions in the primary

equipment. The protection engineer can prepare the necessary optimized and pre-tested

settings in advance for different protection functions. Six different groups of setting

parameters are available in the IED. Any of them can be activated through the different

programmable binary inputs by means of external or internal control signals.

A function block, SETGRPS, defines how many setting groups are used. Setting is done with

parameter

MAXSETGR and shall be set to the required value for each IED. Only the number of

setting groups set will be available in the Parameter Setting tool for activation with the

ActiveGroup function block.

9.4.2

Setting guidelines

M15259-3 v4

The setting

ActiveSetGrp, is used to select which parameter group to be active. The active

group can also be selected with configured input to the function block SETGRPS.

The length of the pulse, sent out by the output signal SETCHGD when an active group has

changed, is set with the parameter

The parameter

MAXSETGR defines the maximum number of setting groups in use to switch

between. Only the selected number of setting groups will be available in the Parameter Setting

tool (PST) for activation with the ActiveGroup function block.

9.5

Signal matrix for binary inputs SMBI

SEMOD55793-1 v2

9.5.1

Application

M15310-3 v2

The Signal matrix for binary inputs function SMBI is used within the Application Configuration

tool in direct relation with the Signal Matrix tool. SMBI represents the way binary inputs are

brought in for one IED configuration.

9.5.2

Setting guidelines

M15312-3 v3

There are no setting parameters for the Signal matrix for binary inputs SMBI available to the

user in Parameter Setting tool. However, the user shall give a name to SMBI instance and the

SMBI inputs, directly in the Application Configuration tool. These names will define SMBI

function in the Signal Matrix tool. The user defined name for the input or output signal will also

appear on the respective output or input signal.

9.6

Signal matrix for binary outputs SMBO

SEMOD55215-1 v2

9.6.1

Application

SEMOD55213-5 v4

The Signal matrix for binary outputs function SMBO is used within the Application

Configuration tool in direct relation with the Signal Matrix tool. SMBO represents the way

binary outputs are sent from one IED configuration.

Section 9

1MRK 511 445-UEN B

Basic IED functions

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды