ABB Relion SAM600 Скачать руководство пользователя страница 71

Страница: 71 / 92

8.4

Denial of service SCHLCCH/RCHLCCH

8.4.1

Application

GUID-64F4D905-9F73-4073-B8F6-8D373155316A v5

The denial of service functionality is designed to limit the CPU load that can be produced by

Ethernet network traffic on the IED. The communication facilities must not be allowed to

compromise the primary functionality of the device. All inbound network traffic will be quota

controlled so that too heavy network loads can be controlled. Heavy network load might for

instance be the result of malfunctioning equipment connected to the network.

The functions Access point diagnostics function block measure the IED load from

communication and, if necessary, limit it for not jeopardizing the IEDs control and protection

functionality due to high CPU load. The function has the following denial of service related

outputs:

•

LINKSTS indicates the Ethernet link status for the rear ports (single communication)

•

CHALISTS and CHBLISTS indicates the Ethernet link status for the rear ports channel A

and B (redundant communication)

•

LinkStatus indicates the Ethernet link status for the front port

8.4.2

Setting guidelines

GUID-CE3344E8-539B-47E0-9C19-8239988BDBCF v3

The function does not have any parameters available in the PCM600.

1MRK 511 445-UEN B

Section 8

Security

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды