ABB Relion SAM600 Скачать руководство пользователя страница 70

Страница: 70 / 92

The information can, in addition to be viewed on the built in HMI, also be retrieved with the aid

of a PC with PCM600 installed and by using the Event Monitoring Tool. The PC can either be

connected to the front port, or to the port at the back of the IED.

8.3

Change lock CHNGLCK

GUID-B48775D0-ACF0-49C6-A7F6-69AF37F1C68F v1

8.3.1

Application

GUID-51EEC9C7-8ECF-4546-BC26-326861654340 v4

Change lock function CHNGLCK is used to block further changes to the IED configuration once

the commissioning is complete. The purpose is to make it impossible to perform inadvertent

IED configuration and setting changes.

However, when activated, CHNGLCK will still allow the following actions that does not involve

reconfiguring of the IED:

•

Monitoring

•

Reading events

•

Resetting events

•

Reading disturbance data

•

Clear disturbances

•

Reset LEDs

•

Reset counters and other runtime component states

•

Control operations

•

Set system time

•

Enter and exit from test mode

•

Change of active setting group

The binary input controlling the function is defined in ACT or SMT. The CHNGLCK function is

configured using ACT.

LOCK

Binary input signal that will activate/deactivate the function, defined in ACT or SMT.

GUID-8C333BC0-AA7A-4ED1-A772-18C22E8EEE62 v6

When CHNGLCK has a logical one on its input, then all attempts to modify the

IED configuration and setting will be denied and the message in PCM600 will be

"Operation denied by active ChangeLock". The CHNGLCK function should be

configured so that it is controlled by a signal from a binary input card. This

guarantees that by setting that signal to a logical zero, CHNGLCK is

deactivated. If any logic is included in the signal path to the CHNGLCK input,

that logic must be designed so that it cannot permanently issue a logical one

to the CHNGLCK input. If such a situation would occur in spite of these

precautions, then please contact the local ABB representative for remedial

action.

Section 8

1MRK 511 445-UEN B

Security

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды