ABB Relion SAM600 Скачать руководство пользователя страница 69

Страница: 69 / 92

Section 8

Security

8.1

Authority status ATHSTAT

SEMOD158575-1 v2

8.1.1

Application

SEMOD158527-5 v3

Authority status (ATHSTAT) function is an indication function block, which informs about two

events related to the IED and the user authorization:

•

the fact that at least one user has tried to log on wrongly into the IED and it was blocked

(the output USRBLKED)

•

the fact that at least one user is logged on (the output LOGGEDON)

The two outputs of ATHSTAT function can be used in the configuration for different indication

and alarming reasons, or can be sent to the station control for the same purpose.

8.2

Self supervision with internal event list INTERRSIG

IP1721-1 v2

8.2.1

Application

M12625-3 v9

The protection and control IEDs have many functions included. The included self-supervision

with internal event list function block provides good supervision of the IED. The fault signals

make it easier to analyze and locate a fault.

Both hardware and software supervision is included and it is also possible to indicate possible

faults through a hardware contact on the power supply module and/or through the

communication.

Internal events are generated by the built-in supervisory functions. The supervisory functions

supervise the status of the various modules in the IED and, in case of failure, a corresponding

event is generated. Similarly, when the failure is corrected, a corresponding event is generated.

Apart from the built-in supervision of the various modules, events are also generated when the

status changes for the:

•

built-in real time clock (in operation/out of order).

•

external time synchronization (in operation/out of order).

Events are also generated:

•

whenever any setting in the IED is changed.

The internal events are time tagged with a resolution of 1 ms and stored in a list. The list can

store up to 40 events. The list is based on the FIFO principle, that is, when it is full, the oldest

event is overwritten. The list contents cannot be modified, but the whole list can be cleared

using the Reset menu in the LHMI.

The list of internal events provides valuable information, which can be used during

commissioning and fault tracing.

1MRK 511 445-UEN B

Section 8

Security

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды