ABB Relion SAM600 Скачать руководство пользователя страница 62

Страница: 62 / 92

To increase security it is recommended to uncheck protocols that are not used

on the access point.

The default gateway can be selected by entering the IP address in

Default gateway. The default

gateway is the router that is used to communicate with the devices in the other subnetwork.

By default this is set to

0.0.0.0 which means that no default gateway is selected. ECT validates

the entered value, but the default gateway has to be in the same subnetwork as the access

point. The default gateway is the router that is being used as default, that is when no route

has been set up for the destination. If communication with a device in another subnetwork is

needed, a route has to be set up. For more information on routes, see the

Routes chapter in

the

Technical manual and the Application manual.

6.2

Redundant communication

6.2.1

Identification

GUID-B7AE0374-0336-42B8-90AF-3AE1C79A4116 v1

Function description

IEC 61850

identification

IEC 60617

identification

ANSI/IEEE C37.2

device number

IEC 62439-3 Parallel redundancy

protocol

PRP

IEC 62439-3 High-availability

seamless redundancy

HSR

Access point diagnostic for

redundant Ethernet ports

RCHLCCH

6.2.2

Application

GUID-172BA5D7-6532-4B0D-8C1D-2E02F70B4FCB v1

Dynamic access point diagnostic (RCHLCCH) is used to supervise and assure redundant

Ethernet communication over two channels. This will secure data transfer even though one

communication channel might not be available for some reason

Parallel Redundancy Protocol (PRP) and High-availability Seamless Redundancy (HSR) provides

redundant communication over station bus running the available communication protocols.

The redundant communication uses two Ethernet ports.

Section 6

1MRK 511 445-UEN B

Ethernet-based communication

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды