manualshive.com logo in svg

ABB Relion SAM600, Руководство по применению

Поделиться
Скачать
ABB Relion SAM600 Скачать руководство пользователя страница 56

Operation

M12179-82 v7

The operation of Disturbance report function DRPRDRE has to be set 

On or Off. If Off is

selected, note that no disturbance report is registered, and none sub-function will operate

(the only general parameter that influences Event list (EL)).

Operation = Off:

•

Disturbance reports are not stored.

•

LED information (yellow - start, red - trip) is not stored or changed.

Operation = On:

•

Disturbance reports are stored, disturbance data can be read from a PC for example using

PCM600.

•

LED information (yellow - start, red - trip) is stored.

Every recording will get a number (0 to 999) which is used as identifier (local HMI, disturbance

handling tool and IEC 61850). An alternative recording identification is date, time and

sequence number. The sequence number is automatically increased by one for each new

recording and is reset to zero at midnight. The maximum number of recordings stored in the

IED is 100. The oldest recording will be overwritten when a new recording arrives (FIFO).

To be able to delete disturbance records, 

Operation parameter has to be On.

The maximum number of recordings depend on each recordings total

recording time. Long recording time will reduce the number of recordings to

less than 100.

The IED flash disk should NOT be used to store any user files. This might cause

disturbance recordings to be deleted due to lack of disk space.

5.4.3.1 

Recording times

M12179-88 v6

The different recording times for Disturbance report are set (the pre-fault time, post-fault

time, and limit time). These recording times affect all sub-functions more or less but not the

Event list (EL) function.

Prefault recording time (

PreFaultRecT) is the recording time before the starting point of the

disturbance.

Postfault recording time (

PostFaultRecT) is the maximum recording time after the

disappearance of the trig-signal.

Recording time limit (

TimeLimit) is the maximum recording time after trig. The parameter

limits the recording time if some trigging condition (fault-time) is very long or permanently

set.

Operation in test mode

M12179-492 v4

If the IED is in test mode and 

OpModeTest = Off. Disturbance report function does not save

any recordings and no LED information is displayed.

Section 5

1MRK 511 445-UEN B

Monitoring

50

Switchgear control unit SAM600-IO

Application manual

© Copyright 2017 ABB. All rights reserved

Содержание Relion SAM600





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды