ABB Relion SAM600 Скачать руководство пользователя страница 43

Страница: 43 / 92

The Boolean 16 to integer conversion function (IB16) will transfer a combination of up to 16

binary inputs INx where 1≤x≤16 to an integer. Each INx represents a value according to the
table below from 0 to 32768. This follows the general formula: INx = 2

x-1

where 1≤x≤16. The sum

of all the values on the activated INx will be available on the output OUT as a sum of the values

of all the inputs INx that are activated. OUT is an integer. When all INx where 1≤x≤16 are

activated that is = Boolean 1 it corresponds to that integer 65535 is available on the output

OUT. IB16 function is designed for receiving up to 16 booleans input locally. If the BLOCK input

is activated, it will freeze the output at the last value.

Values of each of the different OUTx from function block IB16 for 1≤x≤16.

The sum of the value on each INx corresponds to the integer presented on the output OUT on

the function block IB16.

Name of input

Type

Default

Description

Value when

activated

Value when

deactivated

IN1

BOOLEAN

Input 1

IN2

BOOLEAN

Input 2

IN3

BOOLEAN

Input 3

IN4

BOOLEAN

Input 4

IN5

BOOLEAN

Input 5

IN6

BOOLEAN

Input 6

IN7

BOOLEAN

Input 7

IN8

BOOLEAN

Input 8

128

IN9

BOOLEAN

Input 9

256

IN10

BOOLEAN

Input 10

512

IN11

BOOLEAN

Input 11

1024

IN12

BOOLEAN

Input 12

2048

IN13

BOOLEAN

Input 13

4096

IN14

BOOLEAN

Input 14

8192

IN15

BOOLEAN

Input 15

16384

IN16

BOOLEAN

Input 16

32768

The sum of the numbers in column “Value when activated” when all INx (where 1≤x≤16) are

active that is=1; is 65535. 65535 is the highest boolean value that can be converted to an

integer by the IB16 function block.

4.11

Integer to Boolean 16 conversion with logic node

representation ITBGAPC

SEMOD158419-1 v3

4.11.1

Identification

SEMOD167944-2 v4

Function description

IEC 61850

identification

IEC 60617

identification

ANSI/IEEE C37.2

device number

Integer to boolean 16 conversion

with logic node representation

ITBGAPC

1MRK 511 445-UEN B

Section 4

Logic

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды