ABB Relion SAM600 Скачать руководство пользователя страница 38

Страница: 38 / 92

ALMCALH output signal and the physical outputs allows the user to adapt the alarm signal to

physical tripping outputs according to the specific application needs.

4.3.3

Setting guidelines

GUID-0BDD898A-360B-4443-A5CF-7619C80A17F4 v2

Operation: On or Off

4.4

Logic for group alarm WRNCALH

4.4.1

Identification

GUID-3EBD3D5B-F506-4557-88D7-DFC0BD21C690 v4

Function description

IEC 61850

identification

IEC 60617

identification

ANSI/IEEE C37.2

device number

Logic for group warning

WRNCALH

4.4.1.1

Application

GUID-FC0DBB7B-FF86-44BF-83D6-DDF120A176DE v1

Group warning logic function WRNCALH is used to route warning signals to LEDs and/or

output contacts on the IED.

WRNCALH output signal WARNING and the physical outputs allows the user to adapt the

warning signal to physical tripping outputs according to the specific application needs.

4.4.1.2

Setting guidelines

GUID-B08F2636-33DA-4937-92EB-1A8AC0909AB4 v2

OperationOn or Off

4.5

Logic for group indication INDCALH

4.5.1

Identification

GUID-3B5D4371-420D-4249-B6A4-5A168920D635 v4

Function description

IEC 61850

identification

IEC 60617

identification

ANSI/IEEE C37.2

device number

Logic for group indication

INDCALH

4.5.1.1

Application

GUID-9BAD30FB-4B75-4E14-82A8-6A59B09FA6EA v1

Group indication logic function INDCALH is used to route indication signals to different LEDs

and/or output contacts on the IED.

INDCALH output signal IND and the physical outputs allows the user to adapt the indication

signal to physical outputs according to the specific application needs.

4.5.1.2

Setting guidelines

GUID-7E776D39-1A42-4F90-BF50-9B38F494A01E v2

Operation: On or Off

Section 4

1MRK 511 445-UEN B

Logic

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды