ABB Relion SAM600 Скачать руководство пользователя страница 30

Страница: 30 / 92

for both acquiring an external switch position (through the IPOS1 and the IPOS2 inputs) and

represent it through the single line diagram symbols (or use it in the configuration through the

outputs POS1 and POS2) as well as, a command function (controlled by the PSTO input), giving

switching commands through the CMDPOS12 and CMDPOS21 outputs.

The output POSITION is an integer output, showing the actual position as an integer number 0

– 3, where 0 = MidPos, 1 = Open, 2 = Closed and 3 = Error.

VSGAPC is provided with IEC61850 communication for the circuit breaker operation. It is

controlled from the SA system.

3.3.3

Setting guidelines

SEMOD158807-4 v4

Selector mini switch (VSGAPC) function can generate pulsed or steady commands (by setting

the

Mode parameter). When pulsed commands are generated, the length of the pulse can be

set using the

tPulse parameter. Also, being accessible on the single line diagram (SLD), this

function block has two control modes (settable through

CtlModel): Dir Norm and SBO Enh.

3.4

Generic communication function for Double Point

indication DPGAPC

SEMOD55384-1 v4

3.4.1

Identification

GUID-E16EA78F-6DF9-4B37-A92D-5C09827E2297 v3

Function description

IEC 61850

identification

IEC 60617

identification

ANSI/IEEE C37.2

device number

Generic communication function for

Double Point indication

DPGAPC

3.4.2

Application

SEMOD55391-5 v8

Generic communication function for Double Point indication (DPGAPC) function block is used

to send double point position indication to other systems, equipment or functions in the

substation through IEC 61850-8-1 or other communication protocols. It is especially intended

to be used in the interlocking station-wide logics. To be able to get the signals into other

systems, equipment or functions, one must use other tools, described in the Engineering

manual, and define which function block in which systems, equipment or functions should

receive this information.

More specifically, DPGAPC function reports a combined double point position indication

output POSITION, by evaluating the value and the timestamp attributes of the inputs OPEN

and CLOSE, together with the logical input signal VALID.

When the input signal VALID is active, the values of the OPEN and CLOSE inputs determine the

two-bit integer value of the output POSITION. The timestamp of the output POSITION will have

the latest updated timestamp of the inputs OPEN and CLOSE.

When the input signal VALID is inactive, DPGAPC function forces the position to intermediated

state.

When the value of the input signal VALID changes, the timestamp of the output POSITION will

be updated as the time when DPGAPC function detects the change.

Section 3

1MRK 511 445-UEN B

Control

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды