ABB Relion SAM600 Скачать руководство пользователя страница 28

Страница: 28 / 92

At control with enhanced security there is an additional supervision of the status value by the

control object, which means that each command sequence must be terminated by a

termination command.

The parameter

PosDependent gives permission to operate depending on the position

indication, that is, at

Always permitted it is always permitted to operate independent of the

value of the position. At

Not perm at 00/11 it is not permitted to operate if the position is in

bad or intermediate state.

tSelect is the maximum allowed time between the select and the execute command signal,

that is, the time the operator has to perform the command execution after the selection of the

object to operate. When the time has expired, the selected output signal is set to false and a

cause-code is given.

The time parameter

tResResponse is the allowed time from reservation request to the

feedback reservation granted from all bays involved in the reservation function. When the time

has expired, the control function is reset, and a cause-code is given.

tSynchrocheck is the allowed time for the synchrocheck function to fulfill the close conditions.

When the time has expired, the function tries to start the synchronizing function. If

tSynchrocheck is set to 0, no synchrocheck is done, before starting the synchronizing function.

The timer

tSynchronizing supervises that the signal synchronizing in progress is obtained in

SCSWI after start of the synchronizing function. The start signal for the synchronizing is set if

the synchrocheck conditions are not fulfilled. When the time has expired, the control function

is reset, and a cause-code is given. If no synchronizing function is included, the time is set to

which means no start of the synchronizing function is done, and when

tSynchrocheck has

expired, the control function is reset and a cause-code is given.

tExecutionFB is the maximum time between the execute command signal and the command

termination. When the time has expired, the control function is reset and a cause-code is

given.

tPoleDiscord is the allowed time to have discrepancy between the poles at control of three

one-phase breakers. At discrepancy an output signal is activated to be used for trip or alarm,

and during a command, the control function is reset, and a cause-code is given.

SuppressMidPos when On suppresses the mid-position during the time tIntermediate of the

connected switches.

The parameter

InterlockCheck decides if interlock check should be done at both select and

operate, Sel & Op phase, or only at operate, Op phase.

3.2

Logic rotating switch for function selection SLGAPC

SEMOD114936-1 v5

3.2.1

Identification

SEMOD167845-2 v3

Function description

IEC 61850

identification

IEC 60617

identification

ANSI/IEEE C37.2

device number

Logic rotating switch for function

selection and LHMI presentation

SLGAPC

Section 3

1MRK 511 445-UEN B

Control

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды