ABB Relion SAM600 Скачать руководство пользователя страница 26

Страница: 26 / 92

IEC17000101-1-en.vsd

IEC17000101 V1 EN-US

Figure 3:

APC - Local remote function block

3.1.2

Switch controller SCSWI

M16596-3 v6

In SAM600-IO the SCSWI function is used for creating a representation of the combined

position of the one-phase breakers. Ensure that the control part is not used.

SCSWI may handle and operate on one three-phase device or three one-phase switching

devices.

After the selection of an apparatus and before the execution, the switch controller performs

the following checks and actions:

•

A request initiates to reserve other bays to prevent simultaneous operation.

•

Actual position inputs for interlocking information are read and evaluated if the operation

is permitted.

•

The synchrocheck/synchronizing conditions are read and checked, and performs

operation upon positive response.

•

The blocking conditions are evaluated

•

The position indications are evaluated according to given command and its requested

direction (open or closed).

The command sequence is supervised regarding the time between:

•

Select and execute.

•

Select and until the reservation is granted.

•

Execute and the final end position of the apparatus.

•

Execute and valid close conditions from the synchrocheck.

At error the command sequence is cancelled.

In the case when there are three one-phase switches (SXCBR) connected to the switch

controller function, the switch controller will "merge" the position of the three switches to the

resulting three-phase position. In case of a pole discordance situation, that is, the positions of

the one-phase switches are not equal for a time longer than a settable time; an error signal will

be given.

The switch controller is not dependent on the type of switching device SXCBR or SXSWI. The

switch controller represents the content of the SCSWI logical node (according to IEC 61850)

with mandatory functionality.

3.1.3

Switches SXCBR/SXSWI

M16602-3 v7

Switches are functions used to close and interrupt an ac power circuit under normal

conditions, or to interrupt the circuit under fault, or emergency conditions. The intention with

these functions is to represent the lowest level of a power-switching device with or without

Section 3

1MRK 511 445-UEN B

Control

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды