ABB Relion SAM600-IO Скачать руководство пользователя страница 48

Страница: 48 / 108

DO name

DO type

DA name

Signal

Mon/C

Description

Mod

a_dINC

stVal

Mon

Mode status parameter for 61850

Mon

Quality: Mode status parameter

for 61850

Mon

Timestamp: Mode status

parameter for 61850

Beh

a_dINS

stVal

Beh

Mon

Behaviour parameter for 61850

Beh

Mon

Quality: Behaviour parameter for

61850

Beh

Mon

Timestamp: Behaviour parameter

for 61850

ISCSO

b_dINC

Oper.ctlVal

Cmd

Command parameter for

IEC61850

Oper.origin.orCat

Cmd

Command parameter for

IEC61850

Oper.origin.orIdent

Cmd

Command parameter for

IEC61850

Oper.ctlNum

Cmd

Command parameter for

IEC61850

Oper.T

Cmd

Command parameter for

IEC61850

Oper.Test

Cmd

Command parameter for

IEC61850

Oper.Check

Cmd

Command parameter for

IEC61850

stVal

Mon

Integer to be converted to bit

pattern OUT1 to OUT16

Mon

Quality: Integer to be converted

to bit pattern OUT1 to OUT16

Mon

Timestamp: Integer to be

converted to bit pattern OUT1 to

OUT16

ctlModel

Used by CH

7.3.2

Boolean to integer converter FCVI

7.3.2.1

Boolean to integer conversion with logical node representation, 16 bit

BTIGAPC

SEMOD175753-1 v4

PID-6944-LOGICALNODEDATA v2

LN type

LN prefix LN class Function block name

B16IFCVI (revision 0) B16I

FCVI

BTIGAPC

Section 7

1MRK 511 440-UEN A

Logical node data model

Switchgear control unit SAM600-IO Version 2.2 IEC

Communication protocol manual

Содержание Relion SAM600-IO












































































































Результаты поиска

Содержание Relion SAM600-IO

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600-IO, Руководство по протоколу

Результаты поиска

Содержание Relion SAM600-IO

Отзывы:

Бренды по названию

Популярные бренды