manualshive.com logo in svg

ABB Relion REQ650, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB Relion REQ650 Скачать руководство пользователя страница 85

6.4.2 

Two step overvoltage protection OV2PTOV (59)

Prepare the IED for verification of settings as outlined in 

5.1 "Preparing the IED to verify

settings"

.

Values of the logical signals for OV2PTOV (59) are available on the local HMI under

Main menu/Tests/Function status/Voltage/OV2PTOV(59,2U>)/OV2PTOV:1

. The

Signal Monitoring in PCM600 shows the same signals that are available on the local HMI.

6.4.2.1 

Verification of single-phase voltage and time delay to operate for Step 1

1.

Apply single-phase voltage below the set value 

Pickup1

.

2.

Slowly increase the voltage until the PU_ST1 signal appears.

3.

Note the operate value and compare it with the set value.

The operate value in secondary volts is calculated according to the
following equations:

For phase-to-ground measurement:

sec

100

3

Vpickup

VBase

VT

VTprim

>

´

´

ANSIEQUATION2426 V1 EN

(Equation 16)

For phase-to-phase measurement:

sec

100

Vpickup

VT

VBase

VTprim

>

´

´

ANSIEQUATION2427 V1 EN

(Equation 17)

4.

Decrease the voltage slowly and note the reset value.

5.

Set and apply about 20% higher voltage than the measured operate value for one
phase.

6.

Measure the time delay for the TRST1 signal and compare it with the set value.

7.

Check the inverse time delay by injecting a voltage corresponding to 1.2 ×
Vpickup>.

For example, if the inverse time curve A is selected, the trip signals
TRST1 and TRIP operate after a time corresponding to the equation:

( )

1

1

TD

t s

V

Vpickup

=

æ

ö

-

ç

÷

>

è

ø

ANSIEQUATION2429 V1 EN

(Equation 18)

1MRK 505 293-UUS A

Section 6

Testing functionality

77

Commissioning manual

Содержание Relion REQ650























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды