manualshive.com logo in svg

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB Relion 650 Series REL650 Скачать руководство пользователя страница 158

•

Check the IEC61850 and DNP3 communication status in internal event list in

Main menu/Diagnostics/IED Status/General

.

•

In case of persistent faults originating from IED's internal faults such as
component breakdown, contact ABB for repair or replacement actions.

8.1.3.1 

Checking the communication link operation

There are several different communication links on the product. First check that all
communication ports that are used for communication are turned on.

1.

Check the front communication port RJ-45.
1.1. Check that the uplink LED is lit with a steady green light.

The uplink LED is located on the LHMI above the RJ-45 communication
port on the left. The port is used for direct electrical communication to a PC
connected via a crossed-over Ethernet cable.

1.2. Check the communication status of the front port via the LHMI in 

Main

menu/Test/Function status/Communication/1:DOSFRNT/Outputs

.

Check that the 

LINKUP

 value is 1, that is, the communication is working.

When the value is 0, there is no communication link.

The rear port connector X0 is used for connecting an external
HMI to the IED. If the 

LINKUP

 value is 0 for front port, there is

no communication link via port X0. Do not use rear port
connector X0 if the IED is equipped with an LHMI.

2.

Check the communication status of the rear port X1 via the LHMI in 

Main menu/

Test/Function status/Communication/1:DOSLAN1/Outputs

.

The X1 communication port on the rear side of the IED is for optical Ethernet via
LC connector or electrical via RJ-45 connector of the IEC 61850-8-1 station bus
communication.
•

Check that the 

LINKUP

 value is 1, that is, the communication is working.

When the value is 0, there is no communication link.

8.1.3.2 

Checking the time synchronization

•

Select 

Main menu/Diagnostics/IED status/General

 and check the status of the

time synchronization on 

Time Synch

.

The 

Time synch

 value is 

Normal

 when the synchronization is in order.

Section 8

1MRK 506 331-UUS A

Troubleshooting

150

Commissioning Manual

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды