ABB Relion 650 Series REL650 страница 135 Скачать руководство пользователя | Manualshive

Страница: 135 / 176

background image

Values of the logical signals for ZCRWPSCH (85) are available on the local HMI
under

Main menu/Tests/Function status/Scheme communication/ZCRWPSCH(85)/

1:ZCRWPSCH

. The Signal Monitoring in PCM600 shows the same signals that are

available on the local HMI.

The current reversal logic and the weak-end infeed functions are tested during the
secondary-injection test of the impedance or overcurrent protection zones together with
the scheme communication logic for the distance protection function ZCPSCH (85).

6.9.2.1

Current reversal logic

It is possible to check the delay of the CS send signal with

tDelayRev

by changing

from a reverse to a forward fault.

By continuously activating the CR input and changing from a reverse to a forward
fault, the delay

tDelayRev

can be checked.

Checking of current reversal

The reverse zone timer must not operate before the forward zone fault
is applied. The user might need to increase the reverse zone timer
setting during testing of current reversal.

The forward zone timer must be set longer than the

tDelayRev

setting.

1.

Activate the receive (CRL) signal.

2.

Set the healthy condition to an impedance at 50% of the reach of the reverse zone
connected to IRVL.

3.

After the pickup condition is obtained for reverse zone, apply a fault at 50% of
the reach of the forward zone connected to WEIBLK2.

4.

Check that correct trip outputs and external signals are obtained for the type of
fault generated.
The operation time should be about the

tDelayRev

setting longer than the carrier

accelerated trip (TRIP) previously recorded for permissive scheme communication.

5.

Restore the forward and reverse zone timer to its original setting.

6.9.2.2

Weak-end infeed logic at permissive schemes

1MRK 506 331-UUS A

Section 6

Testing functionality

127

Commissioning Manual

«
...
133
134
135
136
137
...
»

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion 650 Series REL650

WORKTUNES WIRELESS

Бренд: 3M Страницы: 23

Бренд: TAZ Страницы: 19

Бренд: Mitsubishi Electric Страницы: 54

Бренд: Mitsubishi Electric Страницы: 66

Бренд: Mitsubishi Electric Страницы: 51

Бренд: Mitsubishi Electric Страницы: 71

Бренд: Mitsubishi Electric Страницы: 80

Бренд: Mitsubishi Electric Страницы: 86

Бренд: Mitsubishi Electric Страницы: 86

Бренд: Mitsubishi Electric Страницы: 109

Бренд: Mitsubishi Electric Страницы: 124

Бренд: Mitsubishi Electric Страницы: 124

Бренд: Globalmediapro Страницы: 2

Бренд: Texas Instruments Страницы: 11

Бренд: RCA Страницы: 4

Бренд: Magnavox Страницы: 56

Бренд: Noark Страницы: 4

Бренд: Kanlux Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды