ABB Relion 650 Series REL650 Скачать руководство пользователя | Manualshive

Страница: 134 / 176

background image

4.

Check that correct trip outputs and external signals are obtained for the type of
fault generated and that the operate time complies with the

tCoord

timer (plus

relay measuring time).

5.

Check that the other zones operate according to their zone times and that a send
(CS) signal is only obtained for the reverse zone.

6.

Check that for a forward fault, carrier send (CS) signal is first obtained from the
delta based fault inception detection (as it is not directional) , and immediately
inhibited by the forward zone.

7.

Activate the IED receive (CR) signal.

8.

Apply a fault condition in the forward directed zone used for scheme
communication tripping.

9.

Check that the no trip from scheme communication occurs.

10. Check that the trip time from the forward directed zone used for scheme

communication tripping complies with the zone timer and that correct trip
outputs, external signals, and indications are obtained for the actual type of fault
generated.

6.9.1.5

Checking of unblocking logic

Check the unblocking function (if the function is required) when checking the
communication scheme.

Command function with continuous unblocking (

Unblock = 1)

Procedure

1.

Activate the guard input signal (CR_GUARD) of the IED.

2.

Using the scheme selected, check that a signal accelerated trip (TRIP) is obtained
when the guard signal is deactivated.

6.9.1.6

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

to

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

to

No

under

Main menu/Tests/

Function test modes/Scheme communication/ZCPSCH(85)/1:ZCPSCH

for the

function, or for each individual function in a chain, to be tested next. Remember to set
the parameter

Blocked

to

Yes

, for each individual function that has been tested.

6.9.2

Current reversal and WEI logic for distance protection 3-

phase ZCRWPSCH (85)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

Section 6

1MRK 506 331-UUS A

Testing functionality

126

Commissioning Manual

«
...
132
133
134
135
136
...
»

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion 650 Series REL650

Jackson H70 Vibe

Бренд: Surewerx Страницы: 2

Бренд: SterileLight Страницы: 4

HVI long Conductor

Бренд: dehn Страницы: 40

Бренд: Vivitek Страницы: 62

Бренд: GE Multilin Страницы: 114

Бренд: 3M Страницы: 3

Бренд: i4Technology Страницы: 7

Бренд: Caleffi solar Страницы: 4

Бренд: Icy Box Страницы: 16

Бренд: ABB Страницы: 124

Бренд: Philips Страницы: 34

Бренд: Philips Страницы: 8

Бренд: Philips Страницы: 36

Бренд: Philips Страницы: 8

Бренд: Philips Страницы: 100

Бренд: Philips Страницы: 38

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды