ABB Relion 650 Series REL650 Скачать руководство пользователя | Manualshive

Страница: 131 / 176

background image

Keep the CB simulator BR closed. Remove the CBREADY signal by opening SRY.

2.

Apply a fault and thereby a PICKUP signal.

3.

Check that no reclosing takes place.

6.8.3.8

Checking the influence of synchronism check (at three-pole reclosing)

1.

Check that the auto-reclosing function is operative, for example, by making a three-
phase reclosing shot with the synchronism check condition.
Remove the SYNC signal.

2.

Apply a fault causing three-phase trip and thereby a PICKUP and a TR3P signal.

3.

Wait for the

tSync

time out limit.

Check that no reclosing is made.

6.8.3.9

Restoring equipment

After the tests, restore the equipment to normal or desired state. Check the following
items in particular.

1.

Check the operation counters.
Reset the counters to zero, if that is the user's preference. The counter reset
function is found in the HMI under

Main menu/Clear/Clear counters/

STBRREC (79, 0->1)

2.

Restore settings that may have been modified for the tests back to normal.

3.

Disconnect the test switch, CB simulating arrangement and test circuits.
Reconnect any links or connection terminals, which may have been opened for
the tests.

4.

Reset indications, alarms and disturbance recordings.
Clearing of the disturbance report must be done via PCM600 using the
Disturbance Handling tool.

6.8.3.10

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

to

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

to

No

under

Main menu/Tests/

Function test modes/Control/STBRREC(79,0->1)/1:STBRREC

for the function, or

for each individual function in a chain, to be tested next. Remember to set the
parameter

Blocked

to

Yes

, for each individual function that has been tested.

1MRK 506 331-UUS A

Section 6

Testing functionality

123

Commissioning Manual

«
...
129
130
131
132
133
...
»

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion 650 Series REL650

Бренд: SW Stahl PROFI Tools Страницы: 2

Бренд: AERMEC Страницы: 20

Бренд: ABB Страницы: 36

Бренд: GE Страницы: 158

PT56WXF90W - DIGITAL PTV MONITOR

Бренд: Panasonic Страницы: 27

BigVizion HDBV3100

Бренд: Optoma Страницы: 52

Бренд: KUSSMAUL Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды