ABB Relion 650 Series REL650 Скачать руководство пользователя | Manualshive

Страница: 129 / 176

background image

If SYNC as an internal function or external device is not operated by the
injection, it may be connected as a permanent high signal or controlled by a switch.

3.

Read and make notes of the reclosing operation counters. Local HMI tree

Main

menu/Tests/Function status/Control/STBRREC(79,0->1)/1:STBRREC

Possibly reset the counters to zero. Counters are reset in the RESET menu. Make
arrangements for the simulation of the CB, for example, as in figure 13.

4.

Make arrangements for indication, recording and time measurements.
The signals for Add 52A, PICKUP, CLOSECMD, READY and other relevant
signals should preferably be arranged for event recording with time tagging. If
that is not possible, other means of time measurement and recording should be
arranged.

6.8.3.2

Switching the auto-reclosing function

Enabled and Disabled

1.

Set the

Operation

setting to

Disabled

and check the state.

2.

Set the

Operation

setting to

Enabled

and check the state, including SETON and

READY.
The CB should be closed and ready.

3.

If external control

Enabled

/

Disabled

is connected, check that it works.

4.

Set

Operation

to

ExternalCtrl

, and use that control to switch

Enabled

and

Disabled

, and check the state of the function.

6.8.3.3

Verifying the auto-reclosing function

Select the test cases to be run according to what is applicable to the particular
application. It can be, for example, three-phase single-shot reclosing or two-shot
reclosing. Below a case with three-phase single-shot reclosing is described.

1.

Set

Operation

=

Enabled

.

2.

If SESRSYN (25) is not to be operated, ensure that the SYNC input is activated.
If the SESRSYN (25) function is to be included, ensure that SESRSYN (25) is
supplied with the appropriate AC quantities.

3.

Simulate CB closed position by closing switch SC to make the BR relay pickup.

4.

Simulate CBREADY by closing the switch SRY, and leave it closed.

5.

Inject AC quantities to give a trip to the BR and to the PICKUP input.
Observe and preferably record the operation. The BR relay shall trip and reclose
(pickup). After reclosing, the SRY switch can be opened for about 5 s and then
closed again.
The auto-reclosing open time and the sequence should be checked, for example in
the event recording. Check also the operation indications (disturbance report) and
the operation counters.

Main menu/Tests/Function status/STBRREC (79, 0-

>1)/1:STBRREC

1MRK 506 331-UUS A

Section 6

Testing functionality

121

Commissioning Manual

«
...
127
128
129
130
131
...
»

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion 650 Series REL650

Бренд: ABB Страницы: 240

Бренд: ABB Страницы: 144

Бренд: Samsung Страницы: 95

Бренд: Samsung Страницы: 59

Бренд: K&K Страницы: 9

AQUASHIELD SYSTEM AQS-900 Series

Бренд: Kelley Страницы: 16

Бренд: LG Страницы: 26

Magnavox 51MP6200D

Бренд: Philips Страницы: 2

MAGNAVOX 7P4830

Бренд: Philips Страницы: 44

Magnavox 7P4830W

Бренд: Philips Страницы: 48

Бренд: STI Страницы: 2

Бренд: Harbour Страницы: 12

Бренд: Vivitek Страницы: 50

Flex 5150 Appliance

Бренд: VERITAS Страницы: 5

Бренд: 3M Страницы: 49

Бренд: Icy Box Страницы: 14

Бренд: Safety Technology International Страницы: 2

Бренд: scheider electric Страницы: 530

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды