manualshive.com logo in svg

ABB Relion 630 Series, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB Relion 630 Series Скачать руководство пользователя страница 38

5.1.3.1 

Checking the communication link operation

There are several different communication links on the product. First check that all
communication ports that are used for communication are turned on.

1.

Check the front communication port RJ-45.
1.1. Check that the uplink LED is lit with a steady green light.

The uplink LED is located on the LHMI above the RJ-45
communication port on the left. The port is used for direct electrical
communication to a PC connected via a crossed-over Ethernet cable.

1.2. Check the communication status of the front port via the LHMI in 

Main

menu/Monitoring/Ethernet/Front port

.

Check that the 

LINKUP

 value is 1, that is, the communication is

working. When the value is 0, there is no communication link.

2.

Check the communication status of the rear port X0 via the LHMI in 

Main

menu/Monitoring/Ethernet/LAN1

.

The X0 communication port on the rear side of the IED is for electrical
communication to a PC connected via a crossed-over Ethernet cable. This
communication port is an alternative to the front communication port.
•

Check that the 

LINKUP

 value is 1, that is, the communication is

working. When the value is 0, there is no communication link.

3.

Check the communication status of the rear port X1 via the LHMI in 

Main

menu/Monitoring/Ethernet/LAN1

.

The X1 communication port on the rear side of the IED is for optical Ethernet
via LC connector or electrical via RJ-45 connector of the IEC 61850-8-1
station bus communication.
•

Check that the 

LINKUP

 value is 1, that is, the communication is

working. When the value is 0, there is no communication link.

5.1.3.2 

Checking the time synchronization

•

Select 

Main menu/Monitoring/IED status

 and check the status of the time

synchronization on 

Time Synch

.

The 

Time synch

 value is 

Ready

 when the synchronization is in order. Note that

the time synchronization source has to be activated. Otherwise the value is
always 

Ready

.

5.1.4 

Running the display test

To run the display test, either use the push buttons or start the test via the menu.

•

Select 

Main menu/Test/LED test

.

•

Press 

 or  simultaneously 

 and 

.

Section 5

1MRS756801 A

Troubleshooting

30

630 series

Commissioning Manual

Содержание Relion 630 Series

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды