manualshive.com logo in svg

ABB REACT-3.6-TL, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB REACT-3.6-TL Скачать руководство пользователя страница 95

- 95 -

000566AG

5 - Installation

C

onnection of RS485 PC serial communication line

The RS485 PC serial communication line on the communication and control 
signal terminal block 

21

 is reserved for connecting the inverter to advanced 

configuration  software  or 

monitoring devices that communicate with the 

proprietary "Aurora" communication protocol. 

Connection of the REACT to advanced configuration software consists 

of first connecting all the units in a chain in the “daisy-chain” (“in-out”) 

configuration, respecting corresponding signals of the RS485 PC serial 

line, and then activating the communication line termination resistance 
in the last element in the chain by setting the switch for RS485 PC line 
termination 

18

 (to the ON position).

The communication line must also be terminated on the first element of the chain which 

usually corresponds to the monitoring device.

RS485 PC

REACT

POWER

       ALAR

M         GF

I                  ES

C          UP   

       DOW

N        ENTE

R

REACT-UNO

REACT-B

ATT

REACT

POWER

       ALAR

M         GF

I                  ES

C          UP   

       DOW

N        ENTE

R

REACT-UNO

REACT-B

ATT

REACT

POWER       A

LARM         G

FI              

    ESC       

   UP          

DOWN        

ENTER

REACT-UNO

REACT-B

ATT

RS485 > USB

Software 

“Aurora 

Manager”

RS 485 • HALF DUPLEX

RESET

TX/

RX

PWR 

OK

RTN

RX/

D-

TX/D+

N.C.

USB

B-T

ype

RS232/RS48

5

PVI-USB

-RS232_485

RS232/485

 Se

l.

=RS232

=RS485

RESET

TX/RX

PWR OK

USB

B-Type

RS232/RS485

RS232/485 SEL.

RS232
RS485

RTN

RX/D-

TX/D+

N.C.

PVI-USB-RS232_485

18

When connecting a single inverter to the monitoring system, activate the 
communication line termination resistance by setting the switch for RS485 
PC line termination 

18

 (to the ON position).

Set a different RS485 address on each inverter of the chain. An address 
can be chosen freely from out of 1 to 63.

The inverter address is set using the display and the keyboard (see the 

specific chapter).

When an RS-485 connection is being used, if one or more inverters 
are added to the system at a later time, it is necessary to remember to 
reset to OFF the switch on the termination resistance being used by the 
inverter which previously was the last in the system.
Each inverter is supplied with one (1) preset RS485 address and with an 
RS485 PC line termination switch 

18

 in the OFF position.

Скачано

 

с

 

сайта

 

интернет

 

магазина

 https://axiomplus.com.ua/

Содержание REACT-3.6-TL















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды