manualshive.com logo in svg

ABB REACT-3.6-TL, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB REACT-3.6-TL Скачать руководство пользователя страница 92

- 92 -

000566AG

5 - Installation

E

xternal backup command connection

The REACT system is equipped with a Backup AC output that can be 
activated in different operating modes that can be set via a display menu. 
Some modes (“Manual 1”, “Manual 4” and “Auto 1”) demand that entry 
into backup is also subordinate to the state of terminal 1 compared to 
terminal 3 on the communication and control signal terminal block 

21

.

When terminal 1 is brought to the same potential as terminal 3 (i.e. 
creating a short circuit between the two terminals on the terminal block), 
entry into backup mode is activated.

The condition of going into backup is shown on the display.

Since this is a digital input, there are no requirements to be observed 
as regards cable cross-section (it only needs to comply with the sizing 
requirement for passing cables through the cable glands and the terminal 
block).

R

emote control connection

The connection and disconnection of the inverter to and from the grid can 
be controlled through an external control.

The function must be enabled in the relevant menu. If the remote control 
function is disabled, the switching on of the inverter is dictated by the 
presence of the normal parameters that allow the inverter to connect to 
the grid.

If the remote control function is on, besides being dictated by the presence 
of the normal parameters that allow the inverter to connect to the grid, 
switching on the inverter also depends on the state of terminal 4 (positive 
state of the remote ON/OFF) with regard to terminal 2 (ON/OFF remote 
negative) on the communication and control signal terminal block 

21

.

When terminal 4 is brought to the same potential as terminal 2 (that is 
to say when a short circuit is created between the two terminals on the 
terminal block), the inverter is disconnected from the grid.
The remote control OFF condition is shown on the display.

Since this is a digital input, there are no requirements to be observed 
as regards cable cross-section (it only needs to comply with the sizing 
requirement for passing cables through the cable glands and the terminal 
block).

21

Impostazioni

Remote ON/OFF

ENTER

Inverter

ENTER

Password 0000

ENTER

Impostazioni

Backup

ENTER

Inverter

ENTER

Password 0000

ENTER

21

Скачано

 

с

 

сайта

 

интернет

 

магазина

 https://axiomplus.com.ua/

Содержание REACT-3.6-TL















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды