manualshive.com logo in svg

ABB REACT-3.6-TL, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB REACT-3.6-TL Скачать руководство пользователя страница 17

- 17 -

000550AG

1 - Introduction and general information

F

ield of use, general conditions 

ABB accepts no liability for damage of any kind that may arise from 
incorrect or careless operations.

You may not use the equipment for a use that does not conform to that provided for in the 

field of use. The equipment MUST NOT be used by inexperienced staff, or even experienced 

staff if carrying out operations on the equipment that fail to comply with the indications in this 
manual and enclosed documentation.

I

ntended or allowed use

The system is designed to optimise self-consumption in residential 
contexts and consists of 

• REACT-UNO (inverter)

 transforms a direct current (DC) from a 

photovoltaic generator (FV) into an alternating current (AC) which can 
be fed into the public distribution grid. 

• REACT-BATT (battery pack)

 temporarily stores unused energy from 

the photovoltaic generator which will subsequently be used when the 
energy demand from users is greater than the energy produced by the 
PV generator

• REACT-MTR (energy meter)

 which measures energy at the 

connection point to the grid and communicates with REACT-UNO in 

order to maximise energy self-sufficiency by managing the storage 

system.

L

imits in field of use

The REACT system can be used only with photovoltaic modules which do not require the 
grounding of one of the input poles, unless accessories are installed which are compatible 
with the inverter and enable this operation to be carried out. In this case you must install an 
isolation transformer on the AC side of the system.
Only a photovoltaic generator consisting of class II modules (in accordance with IEC 61730) 
can be connected as input to the REACT system (do not connect batteries or other power 
sources)
The REACT system can be connected to the electricity grid only in countries for which it has 

been certified/approved.

The REACT system cannot be connected on the DC side in parallel to other inverters to 
convert energy from a photovoltaic generator with a power greater than the nominal power 
of the single inverter.
The REACT system can be used only if all the technical characteristics are observed.
Batteries other than those approved by ABB cannot be connected to the REACT system

Скачано

 

с

 

сайта

 

интернет

 

магазина

 https://axiomplus.com.ua/

Содержание REACT-3.6-TL















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды