ABB REACT-3.6-TL Скачать руководство пользователя страница 127

Страница: 127 / 174

- 127 -

000569BG

7 - Operation

nverter Menu

Select the

Inverter

menu to access the following sub-menus:

Inverter > Statistics

Select

Statistics

to access the following sub-menus:

1. Lifetime

This section of the menu displays the Total statistics:

• Time:

Total operating time

• E-tot:

Total energy produced

• Er-tot:

Total energy taken from grid used to recharge storage system

• P-Peak:

peak power value

• Val. :

Total production value, calculated using the currency and conver-

sion coefficient set in the relevant section of the Settings menu

• CO

Amount of CO

saved compared to fossil fuels

2. Partial

This section of the menu displays the Partial statistics:

• Time:

Partial operating time

• E-par:

Partial energy produced

• Val. :

Partial production value, calculated using the currency and con-

version coefficient set in the relevant section of the Settings menu

• CO

Partial amount of CO

saved

To reset all the meters of this sub-menu, press the ENTER button for
more than 3 seconds. At the end of this time, you will hear a sound re-
peated 3 times.

3. Today

This section of the menu displays today's statistics:

• E-day:

Energy produced today

• Er-day:

Energy taken from the grid today to recharge the storage sy-

stem

• P-Peak:

daily peak power value

• Val. :

Value of today's production, calculated using the currency and

conversion coefficient set in the relevant section of the Settings menu

• CO

Amount of CO

saved daily

4. Last 7 days

This section of the menu displays the statistics for the last 7 days:

• E-7d:

Energy produced over the last 7 days

• Er-7d:

• Val. :

Value of production over the last 7 days, calculated using the

currency and conversion coefficient set in the relevant section of the Set

tings menu

• CO

Amount of CO

saved over the last 7 days

> Statistics

> Self consumpti.

> Self sufficien.

> Ener. from grid

> Ener. to grid

> Ener. to load

> PV en. to load

> PV ener.

> Settings

> Info

> Measures

> Set time

Password 0000

> Set cash

> Set RS485 com

> Country Select

> New password

> SD Update Info

> Energy Policy

Inverter

> Statistics

> Settings

> Vstart

> Input mode

> Input UV Delay

> Service

> Info

> Part No.

> Serial No.

> Firmware

> Remote ON/OFF

> MPPT Scan

> Power Limit.

> Reactive Power

> Autotest

> Alarms

> Backup

> Lifetime

> Partial

> Today

> Last 7 days

> Last 30 days

> Last 365 days

> User Period

Display

> Settings

> Backlight

> Contrast

> Buzzer

> Power Graph

> Language

Meter

> Settings

> Info

> Type

> Part No.

> Serial No.

> FW Rel.

> Measures

> Voltage

> Active Power

> Line current

> Load current

> Frequency

> Meter model

> Meter Address

> Meter com

Battery

> General

****

Load Manager

> info

> Relay Status

****

WIFI Logger

> Settings

> Info

> Part No.

> Serial No.

> View IP

> View Mode

> Restore AP

System

****

Password 0000

> Settings

> Info

> Nom. Cap

> Measures

> Ibat

> Vbat

> Pbat

> RE

> SOC

> SOH

> RT

> Battery Model

> Battery Packs

Password 0000

> Pack 1

> Settings

> Info

> Device Name

> Serial No.

> FW Rel.

> Nom. Capacity

> Init. Capacity

> Status

> Warning

> Alarms

> Measures

> Pack 1 enable

> Smoke Sensor

Password 0000

> Statistics

> Energy dischar.

> E-day

> E-7d

> E-30d

> E-365

> E-tot

> Ibat

> Vbat

> Pbat

> Tbat

> FCC

> RC

> RE

> TED

> SOC

> SOH

> TUT

> TDT

> RT

> CC

Скачано

сайта

интернет

магазина

https://axiomplus.com.ua/

Содержание REACT-3.6-TL















































































































































































Результаты поиска

Содержание REACT-3.6-TL

Отзывы:

Бренды по названию

Популярные бренды

ABB REACT-3.6-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание REACT-3.6-TL

Отзывы:

Бренды по названию

Популярные бренды