ABB +Q951 Скачать руководство пользователя страница 13

Страница: 13 / 56

Code

Name

Safety

3AUA0000048753

Functional safety; Technical guide No. 10

www.abb.com/safety

ABB Safety information and solutions

Options

3AXD50000328659

Emergency stop functions with button monitoring (oQ951+Q984 and
+Q952+Q984) for ACS880 liquid-cooled drives user's manual

3AUA0000085685

ACX-AP-x assistant control panels user's manual

Other documents

Delivered with the drive

Circuit diagrams

Delivered with the drive

Part lists

You can find manuals and other product documents in PDF format on the Internet at

www.abb.com/drives/documents

Terms and abbreviations

Description

Term

Control board built in a housing (often rail-mountable)

Control unit

Frequency converter for controlling AC motors

Drive

Converts direct current and voltage to alternating current and voltage.

Inverter

Inverter bridge, related components and drive DC link capacitors enclosed in a metal
frame or enclosure. Intended for cabinet installation.

Inverter module

Inverter module(s) under control of one control unit, and related components. One
inverter unit typically controls one motor.

Inverter unit

Drive for controlling several motors which are typically coupled to the same machinery.
Includes one supply unit, and one or several inverter units.

Multidrive

Protective earth (ground)

Introduction to the manual 13

Содержание +Q951
























































Результаты поиска

Содержание +Q951

Отзывы:

ABB +Q951, Руководство пользователя, Страница: 13 / 56

Результаты поиска

Содержание +Q951

Отзывы: