ABB +Q951 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 56

ABB +Q951 Скачать руководство пользователя страница 12

Exclusion of liability

ABB is not responsible for the implementation, verification and validation of the overall safety
system. It is the responsibility of the system integrator (or other party) who is responsible
for the overall system and system safety.

The system integrator (or other responsible party) must make sure that the entire
implementation complies with the instructions in this manual, all relevant standards, directives
and local electrical code, and that the system is tested, verified and validated correctly.

Quick reference guide for implementing a safety system

Task

Do a risk assessment according to the relevant standards or regulations, such as ISO 12100.

Select the applicable functional safety standard for the implementation.

Assess safety: analyze and evaluate risks and define risk reduction strategies. Define the safety re-
quirements.

Design the safety system. The part of the design made by ABB is shown in this manual.

Connect the wiring. See the wiring instructions in this manual and the circuit diagrams delivered with
the drive.

Set the parameters related to the safety function (as listed in this manual).

Do the validation test. You can find instructions for the validation test in this manual.

Document the validation test procedure. You can find the guidelines for the validation test report in this
manual.

Related documents

Code

Name

Drive hardware

3AXD50000131457

ACS880-07CLC drives hardware manual

3AXD50000569786

ACS880-07LC drives hardware manual

3AXD50000250295

ACS880-17LC drives hardware manual

3AXD50000251407

ACS880-37LC drives hardware manual

3AXD50000196111

ACS880-107LC inverter units hardware manual

3AXD50000174782

ACS880-207LC IGBT supply units hardware manual

3AXD50000579662

ACS880-307LC…+A018 diode supply units hardware manual

3AXD50000048634

ACS880 liquid-cooled multidrive cabinets and modules electrical planning

3AXD50000048633

ACS880 liquid-cooled multidrive cabinets and modules safety instructions

3AXD50000048635

ACS880 liquid-cooled multidrive cabinets mechanical installation instructions

Drive firmware

3AUA0000085967

ACS880 primary control program firmware manual

3AUA0000098062

ACS880 primary control program quick start-up guide

3AUA0000103295

ACS880 diode supply control program firmware manual

3AUA0000131562

ACS880 IGBT supply control program firmware manual

PC tools

3AUA0000094606

Drive composer start-up and maintenance PC tool user's manual

12 Introduction to the manual

«
...
10
11
12
13
14
...
»

Содержание +Q951

























































Отзывы:

Нет отзывов