ABB PVS800-57B Скачать руководство пользователя страница 74

Страница: 74 / 84

74 Control unit



Layout and connections

Item

Description

I/O

I/O terminals

(refer to

I/O terminals

on page

)

SLOT 1

Fieldbus adapter module connection

SLOT 2

Used for internal connections

SLOT 3

Reserved

SLOT 4

Not in use

X205

Memory unit connection

BATTERY

Not in use

(Holder for real-time clock battery)

AI1

Mode selector for analog input AI1

(I = current, U = voltage)

AI2

Mode selector for analog input AI2

(I = current, U = voltage)

D2D TERM Not in use
DICOM =

DIOGND

Ground selection. Determines whether

DICOM is separated from DIOGND (ie.

the common reference for the digital

inputs floats).

7-segment display

Multicharacter indications show as repeated

sequences of characters

(“U” shows briefly before “o”.)
Control program startup in progress.

(Flashing) Firmware cannot be started.

Memory unit missing or corrupted.

Firmware download from PC to control

unit in progress.

At power-up, the display may show short

indications of, e.g. “1”, “2”, “b” or “U”. This

is normal. If the display ends up showing

any other value than those described, it

indicates a hardware failure.

Содержание PVS800-57B




















































































Результаты поиска

Содержание PVS800-57B

Отзывы:

ABB PVS800-57B, Руководство по оборудованию, Страница: 74 / 84

Результаты поиска

Содержание PVS800-57B

Отзывы: