ABB OmniCore V250XT Скачать руководство пользователя страница 379

Страница: 379 / 456

Troubleshooting flowchart

Trouble shooting drive unit

Turn on power and

wait 1 minute

Check

Link/Acitivity

LED

Check

24V SYS DRV IN/OUT

X1/X2

Check Module

Status LED

Normal

Solid red

Flashing red

Flashing green

Connection ok

Measure

24V SYS DRV IN/OUT

X1/X2

Flashing or
solid yellow

Check

EtherCAT cables

X3/X4/X16/X18

Check

safety cables
X15/X16/X17

Connection ok

Abnormal

Troubleshoot

power unit

Troubleshoot

power unit

Not lit

Reconnect

power cables

Replace drive unit

Reconnect

EtherCAT cables

Replace

EtherCAT cables

Connection ok

Connection
not ok

Reconnect

safety cables

Connection
not ok

Replace

power cables

Connection
not ok

Replace

safety cables

Connection
not ok

Replace drive unit

Firmware

update

Replace drive unit

Connection
not ok

Still
flashing red

Measure

24_BRAKE

X13/X14

Abnormal

Normal

Red

xx2100001982

Troubleshooting procedure

The troubleshooting table is supposed to be used as a detailed instruction together
with the troubleshooting flowchart.

Note

Action

Make sure that the drive unit is operational.

Power on the controller. Check the
Module Status LED (A) on the drive
unit.

xx2100002221

Wait at least 1 min after power-on.
If the Module Status LED is:

•

Off: The drive unit is in the power off
state. Proceed with step

•

Red, steady: Internal error. Proceed with
step

•

Flashing red (~ 1Hz): Firmware error or
self-test failure.
Upgrade the firmware. If the problem
persists, the drive unit may be faulty, see

Replacing the drive unit on page 263

•

Flashing green (~ 1Hz): Communication
error to another module. Proceed with
step

Continues on next page

Product manual - OmniCore V250XT

379

3HAC073447-001 Revision: B

7 Troubleshooting

7.3.3 Troubleshooting the drive unit

Continued

Содержание OmniCore V250XT








































































































































































































































































































































































































































































Результаты поиска

Содержание OmniCore V250XT

Отзывы:

ABB OmniCore V250XT, Руководство по эксплуатации продукта, Страница: 379 / 456

Результаты поиска

Содержание OmniCore V250XT

Отзывы: