ABB OmniCore V250XT Скачать руководство пользователя страница 156

Страница: 156 / 456

4.2 Inspection activities

4.2.1 Inspection of controller

Inspecting the OmniCore V250XT controller

Note/illustration

Action

DANGER

Before doing any work inside the cabinet,
disconnect the mains power. For more
information, see

Electrical safety on

page 28

Location of wrist strap button:

ELECTROSTATIC DISCHARGE
(ESD)

The unit is sensitive to ESD. Before
handling the unit read the safety inform-
ation in section

The unit is sensitive to

ESD on page 43

xx2100000318

Inspect connectors and cabling to make
sure they are securely fastened and
cabling not damaged.

Inspect the fans and ventilation holes to
make sure they are clean.

After inspection: Temporarily turn the
power supply on. Inspect the fans to
make sure they function correctly. Switch
the power off.

156

Product manual - OmniCore V250XT

3HAC073447-001 Revision: B

4 Maintenance

4.2.1 Inspection of controller

Содержание OmniCore V250XT








































































































































































































































































































































































































































































Результаты поиска

Содержание OmniCore V250XT

Отзывы:

ABB OmniCore V250XT, Руководство по эксплуатации продукта, Страница: 156 / 456

Результаты поиска

Содержание OmniCore V250XT

Отзывы: