ABB IRC5 with FlexPendant Скачать руководство пользователя

Страница: 239 / 306

Signal state

Signal

BCERR

BCWAR

BCACT

Interrupted brake check test, program pointer moved from BrakeCheck routine

Signal state

Signal

BCOK

BCERR

BCWAR

BCACT

Configure system parameters

About the system parameters

The configuration of system parameters required for a robot system should be
made before running the brake check.

Note

It is required to restart the IRC5 controller after changing system parameters.

Type Mechanical Unit

All mechanical units for additional axes that shall be supervised must have the
parameters

Activate at Start Up

and

Deactivation Forbidden

set to On. (Supervised

mechanical units must always be active.)

Type Arm

If an axis should be excluded from brake check, set the parameter

Deactivate

Cyclic Brake Check for axis

to On.

Type Brake

If brake check is executed on an additional axis, a lowest safe brake torque must
be defined. A 5% margin is added during the test for setting the fail limit. The
parameter used is

Max Static Arm Torque

defined in on motor side. A warning

limit is set with a higher torque value (depending on the brake).

Operating manual - IRC5 with FlexPendant

239

3HAC050941-001 Revision: G

5 Programming and testing

5.9.6 Brake check service routine

Continued

Содержание IRC5 with FlexPendant



















































































































































































































































































































Результаты поиска

Содержание IRC5 with FlexPendant

Отзывы:

Похожие инструкции для IRC5 with FlexPendant

Бренды по названию

Популярные бренды

ABB IRC5 with FlexPendant, Руководство по эксплуатации

Результаты поиска

Содержание IRC5 with FlexPendant

Отзывы:

Похожие инструкции для IRC5 with FlexPendant

Бренды по названию

Популярные бренды